Adding a line on bar-chart
Hello, I have the following bar chart, it has some metrics and a target line that was defined under the "Scale Marker" section. I would like to add another point of data in the form of a line but I am not sure how to.
Ideally, the card will include this other point as below: (sorry about the ghetto and bad drawing)
The line in question to be added is a Beast Mode calculation, basically an accumulation of a specific metric:
CASE WHEN `Metric` = 'C' THEN sum(sum(`Value`)) over(partition by YEAR(`Date`), `Metric` order by `Date`) ELSE 0 END
Below is a sample of how the raw data looks like for the screenshots.
If anyone has an idea it will be really appreciated. :)
Best Answers
-
Have you tried the Bullet Chart? That might be a good fit for what you are trying to do.
**Check out my Domo Tips & Tricks Videos
**Make sure to any users posts that helped you.
**Please mark as accepted the ones who solved your issue.2 -
@ChristianW , a Bullet Chart would work but there's also a Bar and Line chart type too.
Jae Wilson
Check out my 🎥 Domo Training YouTube Channel 👨💻
**Say "Thanks" by clicking the ❤️ in the post that helped you.
**Please mark the post that solves your problem by clicking on "Accept as Solution"2
Answers
-
Have you tried the Bullet Chart? That might be a good fit for what you are trying to do.
**Check out my Domo Tips & Tricks Videos
**Make sure to any users posts that helped you.
**Please mark as accepted the ones who solved your issue.2 -
@ChristianW , a Bullet Chart would work but there's also a Bar and Line chart type too.
Jae Wilson
Check out my 🎥 Domo Training YouTube Channel 👨💻
**Say "Thanks" by clicking the ❤️ in the post that helped you.
**Please mark the post that solves your problem by clicking on "Accept as Solution"2 -
Hello both, thanks for your answers. Yes, that works perfectly fine, the issue was deeper since I had a beast mode with a window function plus another column with the values. Anyhow, I had to do some ETLing to overcome this otherwise, it would have been extremely difficult to get what I wanted the way the data was structured.
0 -
side note... rewrite your metric
CASE WHEN `Metric` = 'C' THEN sum(sum(`Value`)) over(partition by YEAR(`Date`), `Metric` order by `Date`) ELSE 0 END
Avoid putting aggregations inside of a CASE statement. usually leads to heartache.
Given that it looks like you only want your aggregation to work IF the metric type is C. then write it as
sum(sum(CASE WHEN `Metric` = 'C' then `Value` end )) over(partition by YEAR(`Date`) order by `Date`)
Jae Wilson
Check out my 🎥 Domo Training YouTube Channel 👨💻
**Say "Thanks" by clicking the ❤️ in the post that helped you.
**Please mark the post that solves your problem by clicking on "Accept as Solution"2
Categories
- All Categories
- 1.8K Product Ideas
- 1.8K Ideas Exchange
- 1.6K Connect
- 1.2K Connectors
- 300 Workbench
- 6 Cloud Amplifier
- 9 Federated
- 2.9K Transform
- 102 SQL DataFlows
- 626 Datasets
- 2.2K Magic ETL
- 3.9K Visualize
- 2.5K Charting
- 754 Beast Mode
- 61 App Studio
- 41 Variables
- 693 Automate
- 178 Apps
- 456 APIs & Domo Developer
- 49 Workflows
- 10 DomoAI
- 38 Predict
- 16 Jupyter Workspaces
- 22 R & Python Tiles
- 398 Distribute
- 115 Domo Everywhere
- 276 Scheduled Reports
- 7 Software Integrations
- 130 Manage
- 127 Governance & Security
- 8 Domo Community Gallery
- 38 Product Releases
- 11 Domo University
- 5.4K Community Forums
- 40 Getting Started
- 30 Community Member Introductions
- 110 Community Announcements
- 4.8K Archive